+86 0571-87007056  service@fctel.com.cn

Managed Fiber Media Converter

  • fctel-
  • fctel-
  • fctel-
  • fctel-

GE Fiber Media Converter with remote management(power internal)

Overview
This series of products are Ethernet IEEE802.3 media converters which can realize media conversion between 10/100/1000base-T twisted pair and 1000base-X media or extend the network transmission distance mainly used for long-distance optical fiber networks (20/40/60/80/100 km) transmission fully supports 10/100/1000M transmission rate.
The equipment is based on the Ethernet switching chip + FPGA solution with remote OAM frame management function with powerful local and remote management functions and can be connected to the card fiber transceiver with SNMP network management at the central office or with independent SNMP network management Connected to the optical fiber receiver.
Features
◆ Automatically adapt to the 10/100/1000M environment easy to adapt to the upgrade electrical port MDI/MDI-X of different networks without manual adjustment which is convenient for on-site wiring;
◆ Transceiver device crash monitoring and self-reset functions can work for a long time without crashing in a large-flow video transmission environment greatly reducing the workload of equipment maintenance;
◆ The transceiver has a built-in large-capacity 1Mbits high-rate buffer which can avoid the phenomenon of frame burst caused by the rapid change of the monitoring picture of the IP camera in the environment of the rapid change of the monitoring picture such as the reflection of the car lights on the road at night and rain;
◆ Supports the transmission of VLAN ultra-long data packets supports Ethernet packets with a maximum of 10K bytes or more and is suitable for some giant frame network image transmission protocols;
◆ The device is an Ethernet switching chip + FPGA solution with remote OAM management frame function and can be interconnected with a 2U plug-in card 1 optical 1 electrical transceiver card with SNMP network management. The device can be managed on SNMP software; you can view and Set the device status and parameters of the local end and the opposite end and set the Ethernet bandwidth of the local end and the opposite end;
◆ Support LFP (link Fault Pass Through) function when either the fiber or twisted pair connecting the two ends of the transceiver fails the transceiver will notify the other end to display the fault information;
◆ The device has a power failure detection function which can detect when the optical signal is lost the peer device is powered down or the fiber is blocked;
◆ Ethernet interface with three-level lightning protection anti-radar to GB/T17626.5 (IEC61000-4-5) short-circuit current wave 8/20μs open-circuit peak output voltage 6KV standard;
◆ AC 220V DC-48V DC24V can be optionalDC-48V/DC24V power supply polarity detection function Polarity-Free.
Parameters
Fiber
Optical port: 1
Optical fiber: single fiber and double fiber
Fiber Interface: FC/SC/ST/LC (SFP)
Wavelength: 850nm/1310nm multimode; 1310nm/1550nm single mode
No relay transmission distance: 20~120Km
Typical transmit power:
Single mode 1310/1550nm: ≥-9dBm
Multimode 850nm: -18dBm
Multimode 1310nm: -25dBm
Acceptable sensitivity range: -28dBm~- 40dBm
Ethernet interface(10 /100/1000M)
Interface rate: 10/100 Mbps half/full duplex auto-negotiation
Interface Standard:Compatible with IEEE 802.3 IEEE 802.1Q (VLAN)
MAC Address Capability: 4096
Connector: RJ45 support Auto-MDIX
Working environment
Working temperature: -10°C ~ 50°C
Working Humidity: 5%~95 % (no condensation)
Storage temperature: -40°C ~ 80°C
Storage Humidity: 5%~95 % (no condensation)
Application
GE Fiber Media Converter with remote management
Download